INCOLOY 800 / 800H / 800HT / 825 / ALLOY 800 / 800H / 800HT / 825 Pipes and Tubes

Incoloy pipe (B407/B423) vs tube (B163)

Choose	When	Watch-outs
B407 / B423 pipe	800 / 800H / 800HT to B407; 825 to B423	H/HT need carbon + grain-size control
B163 tube	Tube twin for HX / instrument duty	No B407/B423 tube URLs on this site
Inconel family	Higher-Ni alternative when required	Confirm media before swapping families

Copy-paste RFQ

Incoloy grade: 800 / 800H / 800HT / 825 Form: B407/B423 pipe / B163 tube Size: ____ Wall: ____ Qty: ____ MTC: 3.1/3.2 Destination: ____

Email sales@savoypipinginc.com with destination and any NACE / TPI notes.

Incoloy 800 / 800H / 800HT / 825 Pipe and Tube

UNS N08800 · N08810 · N08811 · N08825 — ASTM B163 / B407 / B423

Savoy Piping Inc. supplies Incoloy (Alloy) 800 series and 825 seamless pipes and tubes for heat and corrosive process service.

800 · 800H · 800HT · 825

What is Incoloy?

Nickel-iron-chromium alloys bridging stainless and high-nickel grades for carburization, oxidation and selected acid services.

Typical applications

• Furnace and heat-exchanger tubing
• Petrochemical reformer / process piping
• Acid and chemical plant lines (825)
• Power and industrial heating systems

Selection guidance

Use H/HT when creep is design-critical. Use 825 for reducing-acid corrosion. Do not free-substitute 800 for 825.

INCOLOY 800 / 800H / 800HT / 825 Pipes and Tubes range

ASTM B163 INCOLOY 800 / 800H / 800HT / 825 / ASME SB163 INCOLOY 800 / 800H / 800HT / 825 / Seamless Tubes

Standard Specification for Seamless Nickel and Nickel Alloy Condenser and Heat-Exchanger Tubes

This specification covers Seamless Tubes of nickel and nickel alloys, as shown in Table 1, for use in condenser and heat-exchanger service.

(A) Maximum unless range or minimum is given. Where ellipses (...) appear in this table, there is no requirement and analysis for the element need not be determined or reported.

(B) Element shall be determined arithmetically by difference.

(A) Maximum unless range or minimum is given. Where ellipses (...) appear in this table, there is no requirement and analysis for the element need not be determined or reported.

(B) Element shall be determined arithmetically by difference.

(C) Alloy UNS N08811: Al + Ti, 0.85 − 1.20.

This specification covers outside diameter and average wall, or outside diameter and minimum wall tube.

The sizes covered by this specification are 3 in. (76.2 mm) and under in outside diameter with minimum wall thicknesses of 0.148 in. (3.76 mm) and under, and with average wall thicknesses of 0.165 in. (4.19 mm) and under.

Tube shall be furnished in the alloys and conditions as shown in Table 2. for small diameter and light wall tube (converter sizes), see Appendix X2.

(A) Alloy UNS N08800 is normally employed in service temperatures up to and including 1100°F (593°C). Alloys UNS N08810, UNS N08811, and UNS N08120 are normally employed in service temperatures above 1100°F (539°C) where resistance to creep and rupture is required, and it is annealed to develop controlled grain size for optimum properties in this temperature range.

The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Keywords

Condenser Tubes - Condensers - Heat Exchanger Tubes - Heat Exchangers - Nickel - Nickel Alloys - Seamless Nickel Alloy Tubes - Seamless Pipes and Tubes

ASTM B407 INCOLOY 800 / 800H / 800HT / 825 / ASME SB167 INCOLOY 800 / 800H / 800HT / 825 / Seamless Tubes

Standard Specification for Nickel-Iron-Chromium Alloy Seamless Pipe and Tube

1.1 This specification2 covers UNS N08120, UNS N08800, UNS N08801, UNS N08810, UNS N08811, UNS N0889, and UNS N06811 in the form of cold-worked and hot-finished annealed seamless pipe and tube. Alloys UNS N08800 and UNS N06811 are normally employed in service temperatures up to and including 1100°F (593°C). Alloys UNS N08120, UNS N08810, UNS N08811, and UNS N0889 are normally employed in service temperatures above 1100°F (593°C) where resistance to creep and rupture is required, and they are annealed to develop controlled grain size for optimum properties in this temperature range.

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Annealing - Cold Working - Creep Resistance - Creep Strength - Forming - Grain Size - High-Temperature Service Applications - High-Temperature Services - Nickel-Iron-Chromium Alloys - Seamless Nickel Alloy Pipes - Seamless Nickel Alloy Tubes - Seamless Pipes and Tubes

ASTM B423 INCOLOY 825 / ASME B423 INCOLOY 825 Seamless Pipes

Standard Specification for Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS N08825, N08221, and N0684) Seamless Pipe and Tube

1.1 This specification2 covers nickel-iron-chromium-molybdenum-copper alloys (UNS N08825, N08221, and N0684)3 in the form of cold-worked and hot-finished seamless pipe and tube intended for general corrosive service. The general requirements for pipe and tube are covered in Specification B829.

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 The following precautionary caveat pertains only to the test methods portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Keywords

Cold Working - Corrosive Service Applications - Forming - Heat Treatment - Nickel-Iron-Chromium Alloys - Nickel-Iron-Chromium-Molybdenum-Copper Alloys - Seamless Nickel Alloy Pipes - Seamless Nickel Alloy Tubes - Seamless Pipes and Tubes

ASTM B829 INCOLOY 825 / ASME B829 INCOLOY 825 Seamless Pipes and Tubes

Standard Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube

This specification contains various requirements that, with the exception of Sections 5 and 10, are mandatory requirements to the following ASTM nickel and nickel alloy, seamless pipe and tube specifications:

1.2 One or more of the test requirements of Section 5 apply only if specifically stated in the product specification or in the purchase order.

1.3 In case of conflict between a requirement of the product specification and a requirement of this general specification, only the requirement of the product specification needs to be satisfied.

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Keywords

Nickel - Nickel Alloys - Seamless Nickel Alloy Pipes - Seamless Nickel Alloy Tubes - Seamless Pipes and Tubes

INCOLOY 800 Seamless Pipes and Tubes Chemical Composition, UNS NO8800

The chemical composition of Inconel Alloy 800 is provided in the table below:

INCOLOY 800H Seamless Pipes and Tubes Chemical Composition, UNS NO8810

The chemical composition of Inconel Alloy 800H is provided in the table below:

INCOLOY 800HT Seamless Pipes and Tubes Chemical Composition, UNS NO8811

The chemical composition of Inconel Alloy 800HT is provided in the table below:

INCOLOY 825 Seamless Pipes and Tubes Chemical Composition, UNS NO8825

The chemical composition of Inconel Alloy 825 is provided in the table below:

Tensile Properties of Incoloy Alloy 825

Table 2. Typical room temperature tensile properties (not for design. Consult the relevant material or product specification for design values)

INCOLOY 800 / 800H / 800HT / 825 Seamless Pipes and Tubes Applications

The Inconel Alloy 600 / 601 / 625 Pipes and Tubes is used in the following Applications:-

• Sulphuric acid piping and vessels
• Phosphoric acid evaporators
• Pickling tank heaters, pickling tanks and equipment
• Chemical process equipment
• Propellor shafts
• Tank trucks
• Calorifiers
• Electrostatic precipitator electrodes
• Hot vessels for food, water and seawater,
• ammonium sulphate vessels
• Expansion bellows
• Marine exhaust systems
• Power station ash hoppers
• Ethylene furnace quench boilersHydrocarbon cracking Valves, fittings and other components exposed to corrosive attack from 1100-1800° F
• Industrial furnaces
• Heat-treating equipment
• Chemical and petrochemical processing
• Super-heater and re-heaters in power plants
• Pressure vessels
• Heat exchanger

Frequently asked questions — Incoloy 800 / 825 Pipe & Tube

800 vs 800H vs 800HT?

All are Ni-Fe-Cr. 800H/800HT control carbon and grain size for elevated-temperature creep strength; use the grade named on the datasheet.

When to use 825?

Alloy 825 (N08825) for sulfuric/phosphoric and mixed acid corrosion — Mo/Cu additions vs the 800 family.

Pipe specs?

B407 for 800/800H/800HT seamless pipe; B423 for 825 pipe; B163 for seamless tube.

Related alloys?

See Inconel 600/625 for higher Ni alloys and Hastelloy for severe chloride/reducing acids.

Export & documentation

We supply this product for domestic and export projects with MTC (EN 10204 3.1 standard; 3.2 / TPI on request). Include destination, Incoterms and inspection needs on the RFQ.