Delivering High Quality Stainless Steel and Alloy Piping Products — Pipes, Tubes, Fittings, Flanges and more for Global Industries.

sales@savoypipinginc.com
Savoy Piping Inc logo

API 5L X60 SSC TESTED Pipe

Hot Rolled Carbon Steel Pipes as per American Petroleum Institute specification API 5L cover Seamless and Welded Line Pipes used for H2S containing gas and Oil Transportation

API 5L X60 SSC Tested Line Pipe

L415 — sour-service / H₂S packages for pipeline transportation


API 5L X60 SSC Tested L415 line pipe

Savoy Piping Inc. supplies API 5L X60 SSC Tested line pipe when the purchase order requires SSC-tested for sulfide stress cracking resistance (NACE TM0177).

Strength guide (API 5L Table 6 PSL1): yield min 415 (60,200) MPa (psi), tensile min 520 (75,400) MPa (psi).

Related: X60 Sour · X60 HIC · X60 SSC · X60 PSL2 Seamless · X60 Pipe

What buyers must specify

SSC (sulfide stress cracking) testing checks cracking under tensile stress in H₂S service, commonly per NACE TM0177. Many sour POs require both HIC and SSC.

Also see: API 5L seamless line pipe hub · Carbon seamless hub · CS buttweld.

Typical enquiry checklist

  • Grade X60 + PSL1/PSL2 + seamless or LSAW/DSAW/HSAW
  • OD/wall, ends, coating, delivery condition
  • NACE / HIC / SSC methods, acceptance and hardness limits
  • EN 10204 3.1 / 3.2 MTC and any third-party inspection

Our API 5L X60 SSC Tested Pipes Range

API 5L X60 SSC Tested Pipe Specification API 5L / ISO 3183 Hot Rolled.
API 5L X60 SSC Tested Pipe Grades API 5L X60 PSL1, PSL 2 / API 5L X60 PSL1, PSL 2 / API 5L X60 PSL1, PSL 2 / API 5L X60 PSL1, PSL 2 / API 5L X56 PSL1, PSL 2 / API 5L X60 PSL1, PSL 2 / API 5L X65 PSL1, PSL 2 / X70 PSL1, PSL 2 / API 5L X70 PSL1 / PSL2 / API 5L X80 PSL1, PSL 2 / ISO 3183 L245 PSL1, PSL 2, ISO 3183 L290 PSL1, PSL 2, ISO 3183 L320 PSL1, PSL2, ISO 3183 L360 PSL1, PSL 2, ISO 3183 L390 PSL1, PSL 2, ISO 3183 L415 PSL1, PSL 2, ISO 3183 L450 PSL1, PSL 2, ISO 3183 L485 PSL1, PSL 2
API 5L X60 SSC Tested Pipe Type Seamless
API 5L X60 SSC Tested Pipe Outer Diameter Size 3/8" NB to 30" NB (Nominal Bore Size)
API 5L X60 SSC Tested Pipe Wall Thicknesss Schedule 20 to Schedule XXS (Heavier On Request) Up to 250 mm Thicknesss
API 5L X60 SSC Tested Pipe Length 5 to 7 Meters, 09 to 13 Meters, Single Random Length, Double Random Length And Customize Size.
API 5L X60 SSC Tested Pipe Ends Plain Ends / Beveled Ends / Coupling
API 5L X60 SSC Tested Pipe Delivery Conditions As Rolled, Normalizing Rolled, Thermomechanical Rolled / Formed, Normalizing Formed, Normalized and Tempered / Quenched and Tempered - BR / N / Q /T
API 5L X60 SSC Tested Pipe Coating Epoxy Coating / Colour Paint Coating / 3LPE Coating.
API 5L X60 SSC Tested Pipe Other Testing NACE MR0175, NACE TM0177, NACE TM0284, SSC TEST, SSC TEST, SWC, H2 SERVICE, IBR, Etc.
API 5L X60 SSC Tested Pipe Dimension All Pipes Is Manufactured and Inspected / Tested to the Relevant standards including ASTM, ASME, API.
API 5L X60 SSC Tested Pipe Value Added Services Draw / Expansion / Machining / Sand Blasting / Shot Blasting / Galavanizing / Heat Treatment
API 5L X60 SSC Tested Pipe Packaging Loose / Bundle / Wooden Pallet / Wooden box-a / Plastic Cloth Wraps / Plastic End Caps / Beveled Protector
API 5L X60 SSC Tested Pipe Shipment & Transportation By Road - Truck / Train, By Sea - Break-bulk Conventional Vessel / FCL (Full Container Load) / LCL (Less Container Load) / 20 Feet Container / 40 Feet
API 5L X60 SSC Tested Pipe Material Test Certificate Manufacturer Test Certificate As Per EN10204 3.1, 3.2 / Laboratory Test Certificate From NABL Approved Lab./ Under Third Party Inspection Agency Like SGS, TUV, DNV, LLOYDS, ABS ETC

Annex H
(normative)
PSL 2 Pipe Ordered for SOUR Service

H.1 Introduction

This annex specifies additional provisions that apply for PSL 2 pipe that is ordered for sour service [see 7.2 c) 51 ] .

NOTE The consequences of sudden failures of metallic components used for the oil and gas production associated with their exposure to H2S- containing production fluids led to the development of NACE MR0175/ISO 15156-1[21] and subsequently EFC publicantion 16[13] ISO 15156-2 used those sources to provide requirements and recommendations for materials qualificantion and selection for Application in environments containing wet H2S in oil and gas production systems. Carbon and low alloy steels selected using ISO 15156—2 are resistant to cracking in defined H2S containing environments in oil and gas production but are not necessarily immune to cracking under all service conditions. Different service conditions might necessitate the alternative testing that is dealt with in ISO 15156—2:2003, Annex B. That annex specifies requirements for qualifying carbon and low alloy steels for H2S service by laboratory testing.

It is the purchaser’s responsibility to select the carbon and low-alloy steels suitable for the intended service.
H.2 Additional information to be supplied by the purchaser

in addition to items a) to g) as specified by 7.1, the purchase order shall indicante which of the following provisions apply for the specific order item:

a) steel casting method for strip or plate used for the manufacture of welded pipe (see H.3.3.2.1);

b) ultrasonic inspection of strip or plate for laminar imperfections (see H.3.3.2.4);

c) supply of helical-seam pipe containing strip/plate end welds (see H.3.3.2.5);

d) chemical composition for intermediate grades (see H.4.1.1);

e) chemical composition for pipe with t > 25,0 mm (0.984 in) (see H.4.1.2);

f) chemical composition limits (see Table H.1, footnotes c), d,) e), f), i), j)and k);

g) frequency of hardness testing of the longitudinal seam weld of HFW or SAW pipe (see Table H.3);

h) SSC test for manufacturing procedure qualificantion (see Table H.3);

i) alternative HIC/SWC test methods and associated acceptance criteria (see H.7.3.1.3);

j) photomicrographs of reportable HIC cracks (see H.7.3.1.4);

k) alternative SSC test methods and associated acceptance criteria for manufacturing procedure qualificantion (see H.7.3.2.2);

l) for pipe with t ≥ 5,0 mm (0.197 in), ultrasonic inspection for laminar imperfections with in extended length of 100 mm (4.0 in) at the pipe ends (see K.2.1.3);

m) magnetic particle inspection for laminar imperfections at each pipe end face/bevel (see K.2.1.4);

Chemical Requirement for API 5L X60 SSC Tested Pipe

Table H.1 --- Chemical Composition for pipe with t ≤25,0 mm (0.984 in)

Steel grade Mass fraction, based upon heat and product analyses
%
maximum		 Carbon
equivalent a
%
maximum
C b Si Mn b P S V Nb Ti Other c, d CE llw CE pcm
SMLS and welded Pipes
L245NS or BNS 0,14 0,40 1,35 0,020 0,003 e f f 0,04 g 0,36 0,19 h
L290NS or X60NS o,14 0,40 1,35 0,020 0,003 e 0,05 0,05 0,04 - 0,36 0,19 h
L320NS or X60NS 0,14 0,40 1,40 0,020 0,003 e 0,07 0,05 0,04 g 0,38 0,20 h
L360NS or X60NS 0,16 0,4 1,65 0,020 0,003 e 0,10 0,05 0,04 g 0,43 0,22 h
L245QS or BQS 0,14 0,40 1,35 0,020 0,003 e 0,04 0,04 0,04 - 0,34 0,19 h
L 29QS or X60QS 0,14 0,40 1,35 0,020 0,003 e 0,04 0,04 0,04 - 0,34 0,19 h
L320QS or X60QS 0,15 0,4 1,40 0,020 0,003 e 0,05 0,05 0,04 - 0,36 0,20 h
L360QS or X60QS 0,16 0,4 1,65 0,020 0,003 e 0,07 0,05 0,04 g 0,39 0,20 h
L390QS or X56QS 0,16 0,4 1,65 0,020 0,003 e 0,07 0,05 0,04 g 0,40 0,21 h
L415QS or X60QS 0,16 0,4 1,65 0,020 0,003 e 0,08 0,05 0,04 g,i,k 0,41 0,22 h
L450QS or X65QS 0,16 0,4 1,65 0,020 0,003 e 0,09 0,05 0,06 g,i,k 0,42 0,22 h
L485QS or X70QS 0,16 0,4 1,65 0,020 0,003 e 0,09 0,05 0,06 g,i,k 0,42 0,22 h
welded pipe
L245MS or BMS 0,10 0,40 1,25 0,020 0,002 e 0,04 0,04 0,04 - - 0,19
L290MS or X60MS 0,10 0,40 1,25 0,020 0,002 e 0,04 0,04 0,04 - - 0,19
L320MS or X60 MS 0,10 0,4 1,35 0,020 0,002 e 0,05 0,05 0,04 - - 0,20
L360MS or X60 MS 0,10 0,4 1,4 0,020 0,002 e 0,05 0,06 0,04 - - 0,20
L390MS or X56 MS 0,10 0,4 1,4 0,020 0,002 e 0,06 0,08 0,04 g - 0,21
L415MS or X60 MS 0,10 0,4 1,4 0,020 0,002 e 0,08 0,08 0,06 g,i - 0,21
L450MS or X65MS 0,10 0,4 1,60 0,020 0,002 e 0,10 0,08 0,06 g,i,j - 0,22
L485MS or X70 MS 0,10 0,4 1,60 0,020 0,002 e 0,10 0,08 0,06 g,i,j - 0,22
a) Based upon product analysis (see 9.2.4 and 9.2.5) The CEllw limits apply if the carbon mass fraction is greater than 0,12 % and the CEpcm limits apply if the carbon mass fraction is less than or equal to 0,12 %.

b) for each reduction of 0,01 % below the specified maximum for carbon, an increase of 0,05 % above the specified maximum for manganese is permissible, up to a maximum increase of 0,20 %.

c) AI total ≤ 0,060 %; N ≤ 0,012 %; AI/N ≥ 2:1 (not applicable to titanium-killed or titanium-treated steel); Cu ≤ 0,35 % (if agreed ,Cu ≤ 0,10 %); Ni ≤ 0,30 %; Cr ≤ 0,30 %; Mo ≤ 0,15 %; B ≤ 0,0005 %.

d) for welded pipe where calcium is intentionally added, unless otherwise agreed, Ca/s ≥ 1,5 if S > 0,0015 % for SMLS and welded Pipes, the calcium concentration shall be ≤ 0,006 %.

e) The maximum limit for sulfur concentration may be increased to ≤ 0,008 % for SMLS pipe and, if agreed, to ≤ 0,006 % for welded pipe. for such higher-sulfur levels in welded pipe, lower Ca/s ratios may be agreed.

f) Unless otherwise agreed, the sum of the niobium and vanadium concentrations shall be ≤ 0,06 %.

g) The sum of the niobium, vanadium and titanium concentrations shall be ≤ 0,15 %.

h) for SMLS pipe, the listed value may be increased by 0,03.

i) If agreed, the molybdenum concentration shall be ≤ 0,35 %.

j) If agreed, the the chromium concentration shall be ≤ 0,4 %.

k) If agreed, Cr concentration shall be ≤ 0,4 % and Ni concentration shall be ≤ 0,50 %.

Mechanical Requirement for API 5L X60 SSC Tested Pipes

Table H.2 ----Requirements for the results of Tensile tests

Pipe steel grade Pipe body of SMLS and welded Pipes Weld seam of HFW and SAW Pipes
Yield strength a

Rto,5
Mpa (psi)

 Tensile strength a

Rm
Mpa (psi)
 Ratio b

Rto,5/Rm

 Elongation on 50 mm
or 2 in
Af
%		 Tensile strength c

Rm
Mpa (psi)
minimum maximum minimum maximum maximum minimum minimum
L245NS or BNS
L245QS or BQS
L245MS or BMS		 24
(35 500)		 40 d
(65 300) d		 415
(60 200)		 760
(110 200)		 0,93 e 415
(60 200)
L290NS or X60NS
L290QS or X60QS
L290MS or X60MS		 29
(42 100)		 495
(71 800)		 415
(60 200)		 760
(110 200)		 0,93 e 415
(60 200)
L320NS or X60NS
L320QS or X60QS
L320MS or X60MS		 320
(60 400)		 605
(76 100)		 435
(63 100)		 760
(110 200)		 0,93 e 435
(63 100)
L360NS or X60NS
L360QS or X60QS
L360MS or X60MS
360
(60 200)		 530
(76 90)		 600
(66 700)		 760
(110 200)		 0,93 e 600
(66 700)
L390QS or X56QS
L390MS or X56MS		 39
(56 600)		 54
(79 000)		 49
(71 100)		 760
(110 200)		 0,93 e 49
(71 100)
L415QS or X60QS
L415MS or X60MS		 415
(60 200)		 565
(81 90)		 600
(75 400)		 760
(110 200)		 0,93 e 600
(75 400)
L450QS or X65QS
L450MS or X65MS		 40
(65 300)		 600
(87 000)		 535
(77 600)		 760
(110 200)		 0,93 e 535
(77 600)
L485MS or X70MS 485
(70 300)		 635
(92 100)		 570
(82 700)		 760
(110 200)		 0,93 e 570
(82 700)

Mechanical Requirement for API 5L X60 SSC Tested Pipe

Table H.2 ----Requirements for the results of Tensile Tests

Pipe steel grade Pipe body of SMLS and welded Pipes Weld seam of HFW and SAW Pipes
Yield strength a

Rto,5
Mpa (psi)

 Tensile strength a

Rm
Mpa (psi)
 Ratio b

Rto,5/Rm

 Elongation on 50 mm
or 2 in
Af
%		 Tensile strength c

Rm
Mpa (psi)
minimum maximum minimum maximum maximum minimum minimum
L245NS or BNS
L245QS or BQS
L245MS or BMS		 24
(35 500)		 40 d
(65 300) d		 415
(60 200)		 760
(110 200)		 0,93 e 415
(60 200)
L290NS or X60NS
L290QS or X60QS
L290MS or X60MS		 29
(42 100)		 495
(71 800)		 415
(60 200)		 760
(110 200)		 0,93 e 415
(60 200)
L320NS or X60NS
L320QS or X60QS
L320MS or X60MS		 320
(60 400)		 605
(76 100)		 435
(63 100)		 760
(110 200)		 0,93 e 435
(63 100)
L360NS or X60NS
L360QS or X60QS
L360MS or X60MS
360
(60 200)		 530
(76 90)		 600
(66 700)		 760
(110 200)		 0,93 e 600
(66 700)
L390QS or X56QS
L390MS or X56MS		 39
(56 600)		 54
(79 000)		 49
(71 100)		 760
(110 200)		 0,93 e 49
(71 100)
L415QS or X60QS
L415MS or X60MS		 415
(60 200)		 565
(81 90)		 600
(75 400)		 760
(110 200)		 0,93 e 600
(75 400)
L450QS or X65QS
L450MS or X65MS		 40
(65 300)		 600
(87 000)		 535
(77 600)		 760
(110 200)		 0,93 e 535
(77 600)
L485MS or X70MS 485
(70 300)		 635
(92 100)		 570
(82 700)		 760
(110 200)		 0,93 e 570
(82 700)
a for intermediate grades, the difference between the specified maximum yield strength and the specified minimum yield strength shall be as given in the table for the next higher grade, and the difference between the specified minimum tensile strength and the specified minimum yield strength shall be as given in the table for the next higher grade, for intermediate grades, the tensile strength shall be ≤ 760 MPa (110 200 psi).b This limit applies for pipe with D >323, 9 mm (12.750 in).

c for intermediate grades, the specified minimum tensile strength for the weld seam shall be the same value as was determined for the pipe body using footnote a).

d for pipe with D< 219,1 mm (8.625 in), the maximum yield strength shall be ≤495 MPa (71 800 psi).

e The specified minimum elongation, Af, on 50mm or 2 in, expressed in percent and rounded to the nearest percent, shall be as determined using the following equation:

api5l pipe elongation values

Where

C is 1 940 for calculations using SI units and 625 000 for calculations using USC units;

A xc is the applicable tensile test piece cross-sectional area, expressed in square millimeters (square inches), as follows:

---- for circular cross-section test pieces, 130 mm2 (0.20 in2) for 12,5 mm (0.500 in) and 8,9 mm (0.350 in) diameter test pieces; and 65 mm2 ( 0.10 in2) for 6,4 mm (0.250 in) diameter test pieces;

---- for full-section test pieces, the lesser of a) 485 mm2 (0.75 in2) and b) the cross-sectional area of the test piece, derived using the specified outside diameter and the specified wall thickness of the pipe, rounded to the nearest 10 mm2 (0.01 in2)

---- for strip test pieces, the lesser of a) 485 mm2( 0.75 in2) and b) the cross-sectional area of the test piece, derived using the specified width of the test piece and the specified wall thickness of the pipe, rounded to the nearest_10 mm2 (0.01 in2); U is the specified minimum tensile strength, expressed in megapascals (pounds per square inch).
H.4.3 HIC/SWC test

The test for evaluation of resistance-to hydrogen- induced cracking shall meet the following acceptance criteria, with each ratio being the maximum permissible average for three sections per test specimen when tested in solution (Environment) A (see ISO 15156-2:2003, Table B.3):

a) crack sensitivity ratio (CSR) ≤ 2 %;

b) crack length ratio (CLR) ≤ 15 %;

c) crack thickness ratio (CTR) ≤ 5 %;

If HIC/SWC tests are conducted in alternative . media (see H.7.3.1.3) to simulate specific service conditions, alternative acceptance criteria may be agreed.
H.4.4 Hardness test

For test pieces subjected to a hardness test (see H.7.3), the hardness in the pipe body, the weld and HAZ shall be ≤ 250 HV10 or 22 HRC (70,6 HR 15N). The maximum acceptabie hareness of an unexposed weld cap and external surface HAZ and base metal may be 275 HV10 or 26 HRC (73,0 HR 15N) where the equipment user agrees to the alternative weld cap hardness limit, the parent pipe wall thickness is greater than 9 mm, the weld cap is not exposed directly to the sour environment and the escape of hydrogen is not impeded, e.g by canthodic protection.

API 5L X60 SSC Tested Pipe Comparative Specifications

The information here is summarized from ASTM Standards and API Specification 5L. Please see the specific standards for more information.

API Specification PSL 1 and PSL 2 Comparison information.

Grade Range A25 THROUGH X70 GR B THROUGH X80 TABLE 1
SIZE Range 0.405 THROUGH 80 4-2/1 THROUGH 80 TABLE 1
TYPE OF Pipe ENDS PLAIN-END, THREADED-END, BEVELLED-END, SPECIAL COUPLING Pipe PLAIN-END TABLE 1
SEAM WELDING ALL METHODS CONTINOUS WELDING LIMITED TO Grade A25 ALL METHODS EXCEPT CONTINOUS AND LASER WELDING TABLE 1
ELECTRIC WELDS: WELDER FREQUENCY NO MINIMUM 100 KHZ MINIMUM 5.1.3.3.2
HEAT TREATMENTS OF ELECTRIC WELDS REQUIRED for GRADES > X60 REQUIRED for ALL GRADES (GR B THROUGH X80) 5.1.3.3.1; J.3.3.2:6.2.7
CHEMISTRY: MAX C for Seamless Pipe 0.28% for GRADES > GR B 0.24% TABLES 2A, 2B
CHEMISTRY: MAX C for Welded Pipe 0.26% for GRADES > GR B 0.22% TABLES 2A, 2B
CHEMISTRY: MAX P 0.03% 0.03% TABLES 2A, 2B
CHEMISTRY: MAX S ONLY WHEN PURCHASES SPECIFIES SR18 0.02% TABLES 2A, 2B
Carbon EQUIVALENT NONE MAXIMUM REQUIRED for EACH GRADE 4.2:4.3:6.1.3: SR15.1
YIELD STRENGTH, MAXIMUM NONE MAXIMUM for EACH GRADE TABLES 3A, 3B
UTS, MAXIMUM NONE REQUIRED MAXIMUM for EACH GRADE TABLES 3A, 3B
FRACTURE TOUGHNESS ONLY WHEN PURCHASER SPECIFIES SR4 REQUIRED for ALL GRADES 6.2.6; 9.3.5: 9.8.4; 9.10.7;
NON-DESTRUCTIVE INSPECTION OF Seamless Pipes PERMITTED SR4 MANDATORY TABLE 14 9.7.2.6
REPARE BY WELDING OF Pipe BODY, PLATE AND SKELP PERMITTED BY AGREEMENT PROHIBITED 5.3.2;9.7.6: B.1;B.2
Certification CERTIFICATES WHEN SPECIFIED PER SR15 PROHIBITED 4.3;9.7.4.4;9.7.6;B.1.2;B.4
TRACEABILITY TRACEABLE ONLY UNTIL ALL TESTS ARE PASSED UNLESS SR15 IS SPECIFIED CERTIFICATES (SR15.1) MANDATORY
TRACEABLE AFTER COMPLETION OF TESTS (SR15.2) MANDATORY		 12.1
5.6

Chemical Requirement of API 5L X60 SSC Tested Pipe
API 5L Specifications Covers Seamless and Welded pipe suitable for use in conveying gas, water, oil, and other liquefied media. The attached requirements cover our offering of API 5L 4th Ed, PSL 1Seamless and Welded; API 5L 4th Ed PSL 2 Seamless & Welded; and API 5L 4th Ed PSL2 Welded only.

Tensile Properties for Seamless and Welded API 5L SSC Tested Steel Pipe
tensile properties data for Seamless and Welded API 5L steel pipe API 5L 4th Ed PSL 1, PSL 2.

Testing Req for Seamless and Welded API 5L SSC Tested steel Pipe
Our API 5L Seamless Pipes hydrostatic and mechanical testing information for all sizes and grades covered by the specification.

Permissible Variation for Seamless and Welded API 5L SSC Tested steel Pipe

Grade A, B, A25 X60 through X80
NPS 2-1/2 and smaller --Seamless and Welded, % +20 -- 12.5 +15 -- 12.5
NPS 3 --Seamless and Welded, % +18 -- 12.5 +15 -- 12.5
NPS 4 through 18 --Seamless and Welded, % +15 -- 12.5 +15 -- 12.5
NPS 20 and larger -- Welded, % +17.5 -- 10.0 +19.5 -- 8.0
NPS 20 and larger -- Seamless, % +15.0 -- 12.5 +17.5 -- 10.0

Marking Requirements

Paint-stenciled or die-stamped manufacturer’s name or mark, Spec 5L, size, weight per foot, grade, process of manufacture, type of steel, length (NPS 4 and larger only). Test pressure when higher than tabulated (NPS 2 and larger only).

Supplemental Annexes for API 5L SSC TestedSeamless and Welded steel Pipe
API Specification 5L contains 15 Supplemental Annexes that address special conditions and/or additional requirements.

API 5L X60 SSC Tested Pipes of Top Approved Companies

API 5L Grade B Pipe Sabic ApprovedSabic Saudi Arabia) API 5L Grade B Pipe ROYAL DUTCH SHELL ApprovedShell API 5L Grade B Pipe ALBA ApprovedALBA (Saudi Arabia) API 5L Grade B Pipe QAFCO ApprovedQAFCO(Qatar) API 5L Grade B Pipe MAADEN ApprovedMaaden(Saudi Arabia) API 5L Grade B Pipe KNPC ApprovedKNPC(Kuwait)
API 5L Grade B Pipe KOC ApprovedKuwait Oil Company(Kuwait) API 5L Grade B Pipe QATAR PETROLEUM ApprovedQatar Petroleum(Qatar) API 5L Grade B Pipe PDO ApprovedPetroleum Development Oman(Oman) API 5L Grade B Pipe ADNCO ApprovedADNOC(United Arab Emirates) API 5L Grade B Pipe ORPIC ApprovedOrpic(Oman) API 5L Grade B Pipe TAKREER ApprovedTakreer(Abu Dhabi)
API 5L Grade B Pipe YASREF ApprovedYASREF(Abu Dhabi) API 5L Grade B Pipe PETROBRAS ApprovedPetrobras(Brazil) API 5L Grade B Pipe PETRONAS ApprovedPetronas(Malaysia) API 5L Grade B Pipe NIOC ApprovedNIOC(Iran) API 5L Grade B Pipe NPDC ApprovedNPDC(Nigeria) API 5L Grade B Pipe EGPC ApprovedEgyptian General petroleum Corporation(Egypt)

Buy API 5L X60 SSC Tested Pipe in Stock through our store at Cheap Prices

  • API SPEC 5L X60 ISO 3183 SSC Tested Pipe
  • API 5L X60 Bare coating SSC Tested Pipe
  • API 5L X60 Spiral Welded SSC Tested Pipe
  • API 5L X60 SCH 80 SSC Tested Pipes
  • API 5L Grade X60 natural gas SSC Tested Pipe
  • hot-dipped galvanized steel API 5L X60 SSC Tested Pipe
  • API 5L X60 Plain End SSC Tested Pipe
  • API 5L X60 SSC Tested Pipes for petroleum and natural gas industries
  • API 5L X60 High Carbon equivalent SSC Tested Pipe
  • API 5L L415 High Pressure SSC Tested Pipe
  • Thread with Coupling or cap API 5L X60 SSC Tested Pipe
  • API 5L X60 3LPE Coated SSC Tested Pipe
  • API 5L X60 3PE Coated SSC Tested steel Pipe
  • Hot Finished Carbon Steel API 5L X60 SSC Tested Pipe
  • API 5L X60 Steel Welded SSC Tested Pipe stockholders
  • API 5L X60 SSC Tested Oil Pipe dealers
  • API 5L X60 Threaded SSC Tested Pipe
  • API 5L X60 Varnish coating SSC Tested Pipe
  • Offshore Service API 5L X60 SSC Tested Pipe
  • API 5L X60 X60 SSC Tested Pipes
  • API 5L L415 PSL2 SSC Tested Pipe Traders
  • CS API 5L X60 SSC Tested Pipe Supplier in Malaysia
  • API 5L X60 3LPP Coated SSC Tested Pipe
  • API 5L X60 SCH STD SSC Tested Pipe
  • API 5L grade L415 SSC Tested Piping Exporter
  • API 5L X60 Square SSC Tested Pipe
  • API 5L X60 Grade SSC Tested Pipe
  • API 5L L415 CS SSC Tested Pipe Distributors
  • API 5L X60 heavier wall ERW SSC Tested Pipe in India
  • API 5L X60 SSC Tested Fluid Pipe
  • API 5L X60 Bevel Ended SSC Tested Pipes
  • API 5L X60 Big Diameter SSC Tested Pipe
  • API 5L X60 SSC Tested Pipe for Structure or Fluid Transportation
  • API 5L X60 Black Coated Material SSC Tested Pipe
  • API Spec 5L X60 Coated SSC Tested Pipe
  • API 5L X60 Casing SSC Tested Pipe
  • API 5L X60 Round SSC Tested Pipe
  • Industrial API 5L X60 Steel SSC Tested Pipe
  • API 5L X60 Anti-Corrosion Coating SSC Tested Pipe
  • API 5L X60 Hollow Section SSC Tested Pipes
  • API 5L X60 SSC Tested Tubes, Tubos / Tubing / Tubular
  • CS API 5L X60 SSC Tested Pipe Stockyards in Mumbai India
  • API 5L X60 rectangular SSC Tested Pipe
  • API 5L X60 Carbon Steel SSC Tested Pipe for Oil and Gas Industry
  • Black Oil Paint API 5L X60 SSC Tested Pipes exporter in Mumbai
  • JIS Standard API 5L Grade L415 SSC Tested Pipe
  • API 5L X60 Oiled painted SSC Tested Pipes
  • Three Layer Polypropelene Coating API 5L L415 SSC Tested Oilfield Pipe
  • API SPEC 5L X60 steel SSC Tested pipe Stocks
  • API 5L X60 Galvanized (GI) SSC Tested Pipe
  • API 5L X60 Carbon Steel Sour Service SSC Tested Pipe
  • API Spec 5L X60 Big Diameter SSC Tested Pipe
  • SSC Tested API 5L X60 Fusion Bonded Epoxy Coated line pipe
  • API 5L L415 SSC Tested Carbon Steel Pipe
  • API 5L Gr. X60 Sour Service CTE Coating SSC Tested Pipe
  • High yield API 5L X60 SSC Tested Seamless Pipe Supplier
  • API 5L Grade X60 Structural Steel SSC Tested Pipe
  • API 5L X60 Black Steel SSC Tested Pipe in Thailand
  • DIN Standard API 5L L415 SSC Tested Pipe
  • API Standard Spec 5L X60 SSC Tested Pipes
  • API X60 SSC Tested FBE Coating Pipe Exporter in Indonesia
  • API 5L L415 PSL1 SSC Tested Pipe in Mumbai
  • ASTM/ASME Standard API 5L X60 SSC Tested Steel Pipe
  • Carbon Steel API 5L X60 SSC Tested Pipe in Singapore
  • API 5L X60 / L415 SSC Tested Petroleum Pipe
  • API 5L X60 Coaltar Enamel Coating SSC Tested Pipe
  • API 5L Carbon Steel X60 SSC Tested Pipes in Turkey

Frequently asked questions — API 5L X60 SSC Tested

What is API 5L X60 SSC Tested pipe?

It is API 5L X60 (L415) line pipe ordered with SSC-tested for sulfide stress cracking resistance (NACE TM0177).

Is PSL2 the same as sour service?

No. PSL2 is a product specification level. Sour service needs explicit H₂S chemistry and HIC/SSC testing on the PO.

HIC vs SSC?

HIC addresses blistering/stepwise cracking in the pipe body (TM0284). SSC addresses sulfide stress cracking under tension (TM0177). Many sour jobs require both.

Do you supply X60 seamless and welded sour packages?

Yes — seamless and welded forms when the mill route and annex package are confirmed for the size/wall.

Supplying API 5L X60 SSC Tested Pipe to Countries -

We Export API 5L X60 SSC Tested Pipe to Saudi Arabia, Iran, Iraq, United Arab Emirates, Qatar, Bahrain, Oman, Kuwait, Turkey, Egypt, Yemen, Syria, Israel, Jordan, Cyprus, Singapore, Malaysia, Indonesia, Thailand, Vietnam, South Korea, Japan, Sri Lanka, Maldives, Bangladesh, Myanmar, Taiwan, Cambodia, Argentina, Bolivia, Brazil, Chile, Venezuela, Colombia, Ecuador, Guyana, Paraguay, Uruguay, United States of America, Canada, Mexico, Panama, Costa Rica, Puerto Rico, Trinidad And Tobago, Jamaica, Bahamas, Denmark, Russia, Norway, Germany, France, Italy, United Kingdom, Spain, Ukraine, Netherlands, Belgium, Greece, Czech Republic, Portugal, Hungary, Albania, Austria, Switzerland, Slovakia, Finland, Ireland, Croatia, Slovenia, Malta, Nigeria, Algeria, Angola, South Africa, Libya, Egypt, Sudan, Equatorial Guinea, The Republic Of Congo, Gabon, Europe, Africa, Asia, North America, South America, Middle East, Far East.etc

Savoy Piping Inc. is a well known worldwide exporter of API 5L X60 SSC Tested Pipe, Savoy Piping Inc. is committed to provide each and every customer with the highest standard of customer service. We deal in API 5L X60 SSC Tested Pipe in India and Overseas, offering a wide range of API 5L X60 SSC Tested Pipes

SSC test procedure, SSC tested carbon steel, SSC test Wikipedia, SSC test acceptance criteria, ssc testing, SSC test for Seamless Pipe, SSC test for stainless steel, SSC test report, sour service material selection, what is sour service in oil and gas, sour service requirements, sour service line pipe, sour service pipeline, material selection for sour service environment, what is non sour service in oil and gas, sour service wiki, API 5L X42, X46, X52, X56, X60, X65, X70 Pipe SSC Tested Pipe, SOUR Service Pipe, API 5L SSC Line Pipe, SSC Tested Line Pipe, SOUR Service Line Pipes

We provide API 5L SSC Tested SOUR Service Pipe in Grade B, X42, X46, X52, X56, X60, X65 with PSL1 and PSL2. We Carry Complete Range from 3/8" NB to 24" NB, wall Thicknesss upto 200 MM. Savoy Piping Inc. API 5L Grade B Pipe are known for its High Quality and Competitive Price.