Delivering High Quality Stainless Steel and Alloy Piping Products — Pipes, Tubes, Fittings, Flanges and more for Global Industries.
sales@savoypipinginc.com
Delivering High Quality Stainless Steel and Alloy Piping Products — Pipes, Tubes, Fittings, Flanges and more for Global Industries.
sales@savoypipinginc.com
The EN 1092-1 Type 02 Flange and Type 04 flanges both belongs to the cantegory of Loose Plate Flange, serving a similar purpose as the lap joint flanges in ASME B16.5. They can be considered as a variation of the Type 01 slip-on plate flange, featuring an enlarged bore diameter and a chamfered end that facilitates the insertion of a lapped collar. To ensure uniformity, bolt holes are drilled along the periphery of the round plate.
Although EN 1092-1 Type 02 Flanges and Type 04 loose plate flanges share common characteristics, there are subtle distinctions between them. Notably, the bore diameter of Type 04 flanges is significantly larger than that of EN 1092-1 Type 2 Flange of the same size and pressure rating. This distinction arises from the requirement that Type 04 flanges must be able to accommodate the larger neck outside diameter of a tapered collar, specifically referred to as Type 34. EN 1092-1 specifies that Type 02 Loose Plate Flanges are manufactured in eight different pressure ratings: PN 2.5, PN 6, PN 10, PN 16, PN 25, PN 40, PN 63, and PN 100. The Scorresponding dimensions and masses for these flanges can be found in the tables below. All measurements are provided in millimeters (mm), while the weight is given in kilograms (kg).
EN 1092-1 Type 02 Flange & Type 04 Loose plate flanges are primarily made from a series of Carbon steel or Low Alloy Steel Material grades such as P250GH, P24GH, S235JR, A105, P280GH, 16Mo3, P235GH, P265GH, P355NH, P355QH, etc. They can be made by a forging process or machined from bars or plates. They may also be made by a combined bending and electric welding process. EN 1092-1 Type 02 and Type 04 loose plate flanges, along with their corresponding collar assemblies, find primary Application in various piping systems that require frequent dismantling for inspection or routine maintenance. They are also well-suited for the installation of large diameter or complex piping configurations, as they enable quick alignment of bolt holes. Particularly in high alloy pipe work, utilizing a high alloy collar with a carbon steel loose Plate Flange proves more cost-effective than using a complete high alloy flange.
These flanges are commonly employed in mild service scenarios where the loads exerted by the pipe on the flange connection are minimal. It is crucial to meticulously calculate the longitudinal stresses in the piping resulting from pressure, weight, and thermal expansion. Type 02 flanges are offered in PN designations ranging from PN 2.5 to PN 40, while Type 04 flanges are available in PN designations from PN 10 to PN 40.
EN 1092-1 Flanges European Standard for a single series of flanges specïfies requirements for circular steel flanges in PN designations PN 2.5 to PN 100 and nominal sizes from DN 10 to DN 4000. EN 1092-1 Flanges Standard specifies the Flange Types and their Facings, Dimensions, Tolerances, Threading, Bolt Sizes, Flange Jointing Face Surface Finish, Marking, Materials, Pressure / Temperature Ratings and Approximate Flange Masses.
Savoy Piping Inc. are recognized as the prominent Manufacturer, Exporter and Supplier of a broad assortment of EN 1092-1 Flanges in EN 1092-01 Type 01, EN 1092-01 Type 05, EN 1092-01 Type 11, EN 1092-01 Type 12, EN 1092-01 Type 13 etc.
Material of Composition EN 1092-01 Carbon Steel Flange, EN 1092-01 Alloy Steel Flanges, EN 1092-1 Stainless Steel Flanges, EN 1092-01 Duplex Steel Flanges, EN 1092-01 Super Duplex Steel Flanges, with Pressure / Temperature Ratings of PN6, PN10, PN16, PN25, PN40, PN63, PN100. Popular Type of EN 1092-01 Flanges in Compare to ASTM / ASME / DIN Standards are EN 1091-1 Weld-neck Flanges, EN 1091-1 Plate Flanges, EN 1091-1 Blind Flanges,Forged Flange, EN 1091-1 Hubbed Slip-on Flanges, EN 1091-1 Hubbed Threaded Flanges, EN 1091-1 Long Weld Neck Flanges etc.
The offered EN 1092-1 Flanges is Designed with Utmost Precision in Conformity with the International European Quality Standards.Additionally,it aligns with other international flange standards like ANSI, ASME, and DIN, ensuring global compatibility.
| EN 1092-01 Type 02 Flanges Specification & Standard | DIN EN 1092-01 European Standard |
| EN 1092-01 Type 02 Flanges Manufacturing Process | Hot Forging / Steel Casting / Hot Rolled / Plate Machining |
| IS 1092-01 Type 02 Flanges Outer Diameter | DN 15 to DN 4000 |
| EN 1092-01 Type 02 Flanges Pressure Class | PN 2.5, PN 6, PN 8, PN 10, PN 16, PN 25, PN 40, PN 63, PN 100 etc |
| IS 1092-01 Type 02 Flanges Facing | Type Flat Face (FF), Type B Raised Face (RF),Raised Face Flange , Type C Tongue, Type D Groove, Type E Spigot, Type F Recess, Type G O-ring Spigot, Type H O-ring Groove, |
| IS 1092-01 Type 02 Flanges Types | Type 01 Plate Flange for welding, Type 02 Loose Plate Flange with Weld-on Plate Collar or for Lapped Pipe End, Type 04 Loose Plate Flange with weld-neck collar, Type 05 Blind Flange, Type 11 Weld-neck Flange, Type 12 Hubbed Slip-on Flange for welding, Type 13 Hubbed Threaded Flange, Type 34 Weld-neck collar Flange, Type 35 Weldring neck Flange, Type 36 Pressed collar with long neck Flange, Type 37 Pressed collar Flange,WNRF Flange, SORF Flange, BLRF Flange, Custom Flange as per Drawing etc. |
| EN 1092-01 Type 02 Flanges Specicantion, Grades, Symbol, Material Number | EN Series - EN 10028-2, EN 10028-3, EN 10028-4, EN 10028-7, EN 10222-2, EN 10222-3, EN 10222-4, EN 10222-5, EN 10272, EN 10273 Material Name - 10CrMo9-10, 11MnNi5-3, 12CrMo9-10, 12Ni14, 13CrMo4-5, 13MnNi6-3, 15NiMn6, 16Mo3, G17CrMo5-5, G17CrMo9-10, G17Mn5, G20Mn5, G20Mo5, G9Ni10, G9Ni14, GP240GH, GP280GH, GX15CrMo5, GX23CrMoV12-1, GX2CrNi19-11, GX2CrNiMo19-11- 2, GX2CrNiMoCuN25-6-3-3, GX2CrNiMoN22-5- 3, GX2CrNiMoN26-7- 4, GX2NiCrMo28-20- 2, GX5CrNi19-10, GX5CrNiMo19-11- 2, GX5CrNiMoNb19- 11-2, GX5CrNiNb19-11, P235GH, P24GH, P250GH, P265GH, P275NH, P275NL1, P275NL2, P280GH, P285NH, P285QH, P295GH, P355N, P355NH, P355NL1, P355NL2, P355QH, P355QH1, X10CrMoVNb 9-1, X10CrMoVNb9-1, X12 Ni 5, X12Ni5, X16CrMo5-1+NT, X1CrNi25-21, X1CrNiMoCuN20- 18-7, X1CrNiMoCuN20-18-7, X1NiCrMoCu25- 20-5, X1NiCrMoCu31- 27-4, X1NiCrMoCuN25- 20-7, X1NiCrMoCuN25-20-7, X20CrMoV11- 1, X2CrNi18-9, X2CrNi19-11, X2CrNiMo17- 12-2, X2CrNiMo17- 12-3, X2CrNiMo17-12- 2, X2CrNiMo18- 14-3, X2CrNiMo18-14- 3, X2CrNiMoN1 7-11-2, X2CrNiMoN1 7-13-3, X2CrNiMoN17- 11-2, X2CrNiMoN17- 13-3, X2CrNiMoN17- 13-5, X2CrNiMoN2 2-5-3, X2CrNiMoN2 5-7-4, X2CrNiMoN22- 5-3, X2CrNiMoN22-5- 3, X2CrNiMoN25- 7-4, X2CrNiMoN25-7- 4, X2CrNiN18- 10, X2CrNiN18-10, X2CrNiN23-4, X3CrNiMo17- 13-3, X3CrNiMo17-13- 3, X5CrNi18-10, X5CrNiMo17- 12-2, X5CrNiMo17-12- 2, X6CrNi18-10, X6CrNiMoNb17- 12-2, X6CrNiMoTi1 7-12-2, X6CrNiNb18- 10, X6CrNiNb18-10, X6CrNiTi18- 10, X6CrNiTi18-10, X6CrNiTiB18- 10, X6CrNiTiB18-10, X8Ni9 Material Number - 1.034, 1.0352, 1.0425, 1.0426, 1.0460, 1.0477, 1.0478, 1.0481, 1.0487, 1.0488, 1.0562, 1.0565, 1.0566, 1.0571, 1.0619, 1.0625, 1.1104, 1.1106, 1.1131, 1.4301, 1.4306, 1.4307, 1.4308, 1.4309, 1.4311, 1.4335, 1.4362,1.4401, 1.4404, 1.4406, 1.4409, 1.4410, 1.4429, 1.4432, 1.4435, 1.4436, 1.4439, 1.448, 1.4462, 1.429, 1.439, 1.441, 1.447, 1.450, 1.452, 1.463, 1.471, 1.480, 1.493, 1.4922, 1.4931, 1.4941, 1.4948, 1.5415, 1.5419, 1.5636, 1.5637, 1.5638, 1.5662, 1.5680, 1.6212, 1.6217, 1.6220, 1.6228, 1.7335, 1.7357, 1.7365, 1.7366, 1.7375, 1.7379, 1.7380, 1.7383, 1.8867 |
| EN 1092-01 Type 02 Flanges Dimension | EN 1092-1, ASME B16.5, ASME B16.47 SERIES A, ASME B16.47 SERIES B, ASME B16.36, BS10, EN1092-1:2013, MSS SP44, ASA, API-605,ISO Certificante, ISO 7005, ISO 1559-3, DIN 2631--2638, DIN 2573-2576, DIN 2527, DIN 2641-2642, DIN 2565-2566, DIN2502, AWWA, AS2129 TABLE C, D, E, F, J etc.. |
| EN 1092-01 Type 02 Flanges Other Testing | NACE MR0175, Ultrasounic Test, Charpy Impact Test, Macro, Post-weld Heat Treatment (PWHT), Grain Size, Hardness, HIC, SSC, Sour Service, A for annealed, N for normalized, NT for Normalized and Tempered, or QT for Quenched and Tempered, Carbon Equivalent, Dye Penetrant Test etc. |
| EN 1092-01 Type 02 Flanges Value Added Services | Rolling, Drill, Punch, CNC Machining, Sand Blasting, Shot Blasting, Heat Treatment, Anti-rust Paint, Oil Black Paint, Yellow Transparent, Zinc Plated, Cold and Hot Dip Galvanized |
| EN 1092-01 Type 02 Flanges Packaging | Loose / Carrate / Wooden Pallet / Wooden Box / Plastic Cloth Wraps |
| EN 1092-01 Type 02 Flanges Shipment & Transportation | By Road - Truck / Train Partial Load, Full Load, By Sea - Break-bulk Conventional Vessel / FCL (Full Container Load) / LCL (Less Container Load) / 20 Feet Container / 40 Feet Container / 4 Feet Container / High Cube Container / Open Top Container, By Air - Freighter Civil Passenger and Cargo Planes |
| EN 1092-01 Type 02 Flanges Material Test Certificate | Manufacturer Test Certificante As Per EN10204 3.1, 3.2 / RINA Approved / PED Approved / Mill Certificante /Laboratory Test Certificante From NABL Approved Lab. / Under Third Party Inspection Agency Like SGS, TUV, DNV, LLOYDS, ABS, Bureau of Indian Standards BIS Approved etc. |
 EN 1092-1 Type 34 C Tongue |
 EN 1092-1 Type 34 C Tongue |
 EN 1092-1 Type 34 C Tongue |
 EN 1092-1 Type F Recess |
 EN 1092-1 Type F Recess |
 EN 1092-1 Type F Recess |
 EN 1092-1 Type G O Ring Groove |
 EN 1092-1 Type H O Ring Spigot |
|
NOTE 1 The transition from the edge of the raised face to the flange face can be by radius or chamfer for types B, D, F and G only (see 5.7.1). |
|||
|
|
| Correlation of the flange sizes & types covered by the older DIN Standards with those included in DIN EN 1092-1 | ||||
|---|---|---|---|---|
| DIN Standard | Flange type as in DIN EN 1092-1 | Item description | Size range (DN) as in DIN Standard | Size range (DN) as in DIN EN 1092-1 |
| *2512 | – | Tongue and groove | Up to PN 160 DN 4 to DN 1000 | Up to PN 100 DN 10 to DN 2000 |
| *2513 | – | Spigot and recess | DN 10 to DN 1000 | Up to PN 100 DN 10 to DN 2000 |
| *2514 | – | Spigot with groove and recess | DN 10 to DN 3000 | Up to PN 100 DN 10 to DN 2000 |
| 2527 | 05 | Blank flanges, PN 2,5 | Not specified. | DN 10 to DN 2000 |
| 05 | Blank flanges, PN 6 | DN 10 to DN 500 | DN 10 to DN 2000 | |
| 05 | Blank flanges, PN 10 | DN 10 to DN 500 | DN 10 to DN 1200 | |
| 05 | Blank flanges, PN 16 | DN 10 to DN 500 | DN 10 to DN 1200 | |
| 05 | Blank flanges, PN 25 | DN 10 to DN 500 | DN 10 to DN 600 | |
| 05 | Blank flanges, PN 40 | DN 10 to DN 500 | DN 10 to DN 600 | |
| 05 | Blank flanges, PN 64 (now PN 63) | DN 10 to DN 400 | DN 10 to DN 400 | |
| 05 | Blank flanges, PN 100 | DN 10 to DN 350 | DN 10 to DN 350 | |
| 2543 | – | Cast steel flanges, PN 16 | DN 10 to DN 2200 | DN 10 to DN 2000 |
| 2544 | – | Cast steel flanges, PN 25 | DN 10 to DN 2000 | DN 10 to DN 2000 |
| 254 | – | Cast steel flanges, PN 40 | DN 10 to DN 1600 | DN 10 to DN 600 |
| 2546 | – | Cast steel flanges, PN 64 (now PN 63) | DN 10 to DN 1200 | DN 10 to DN 1200 |
| 2547 | – | Cast steel flanges, PN 100 | DN 125 to DN 700 | DN 10 to DN 500 |
| 2566 | 13 | Hubbed threaded flanges, PN 10 to PN 16 | DN 6 to DN 100 | DN 10 to DN 600 |
| 2573 | 01 | Plate flanges for brazing or welding, PN 6 | DN 10 to DN 500 | DN 10 to DN 600 |
| 2576 | 01 | Plate flanges for brazing or welding, PN 10 | DN 10 to DN 500 | DN 10 to DN 600 |
| 2630 | 11 | Weld-neck flanges, PN 1 and PN 2,5 | DN 10 to DN 4000 | DN 10 to DN 4000 |
| 2631 | 11 | Weld-neck flanges, PN 6 | DN 10 to DN 3600 | DN 10 to DN 3600 |
| 2632 | 11 | Weld-neck flanges, PN 10 | DN 10 to DN 3000 | DN 10 to DN 3000 |
| 2633 | 11 | Weld-neck flanges, PN 16 | DN 10 to DN 2000 | DN 10 to DN 2000 |
| 2634 | 11 | Weld-neck flanges, PN 25 | DN 10 to DN 1000 | DN 10 to DN 1000 |
| 2635 | 11 | Weld-neck flanges, PN 40 | DN 10 to DN 500 | DN 10 to DN 600 |
| 2636 | 11 | Weld-neck flanges, PN 64 (now PN 63) | DN 10 to DN 400 | DN 10 to DN 400 |
| 2637 | 11 | Weld-neck flanges, PN 100 | DN 10 to DN 350 | DN 10 to DN 350 |
| 2641 | 02, 33, 32 | Loose plate flanges, lapped pipe ends, weld-on plate collars, PN 6 | DN 10 to DN 1200 | DN 10 to DN 600 |
| 2642 | 02, 33, 32 | Loose plate flanges, lapped pipe ends, weld-on plate collars, PN 10 | DN 10 to DN 800 | DN 10 to DN 600 |
| 2655 | 02, 33, 32 | Loose plate flanges, weld-on plate collars, PN 25 | DN 10 to DN 500 | DN 10 to DN 600 |
| 2656 | 02, 33, 32 | Loose plate flanges, weld-on plate collars, PN 40 | DN 10 to DN 400 | DN 10 to DN 600 |
| 2673 | 04, 34 | Loose plate flanges with weld-neck collar, PN 10 | DN 10 to DN 1200 | DN 10 to DN 600 |
| *Flange feature only; not the call out for a complete flange | ||||
| DIN Plate Flanges (Slip On Flanges) | DIN Weld Neck Flanges | DIN Blind Flanges | DIN Threaded Flanges |
| DIN 2573 PN6 Flanges DIN 2576 PN10 Flanges DIN 2502 PN16 Flanges DIN 2503 PN25 Flanges DIN 2543 PN16 Flanges |
DIN 2631 PN6 Flanges DIN 2632 PN10 Flanges DIN 2633 PN16 Flanges DIN 2634 PN25 Flanges DIN 2635 PN40 Flanges |
DIN 2527 PN6 Flanges DIN 2527 PN10 Flanges DIN 2527 PN16 Flanges DIN 2527 PN25 Flanges DIN 2527 PN40 Flanges |
DIN 2565 PN6 Flanges DIN 2566 PN16 Flanges |
| Some Flange feature equivalents: DIN EN 1092 from DIN | |
|---|---|
| DIN EN 1092-1 | DIN |
| DIN EN 1092-1 Type B Raised Face | DIN 2526 Form C |
| DIN EN 1092-1 Type C Tongue | DIN 2512 Feder (Form F) |
| DIN EN 1092-1 Type D Groove | DIN 2512 Nut (Form N) |
| DIN EN 1092-1 Type E Spigot | DIN 2513 Vorsprung (Form V) |
| DIN EN 1092-1 Type F Recess | DIN 2513 Rücksprung (Form R) |
We canter to Diverse Industries, including Oil and Gas, where EN 1092-1 Type 02 Flanges find Extensive Applications. Our EN 1092-1 Flanges Solutions meet Stringent Specifications and Industry Standards, Making them Ideal for High-Temperature Pipe Bending in Demanding Environments - Oil and Gas Equipments, Offshore Technology, Seawater Desalination Plants, Chemical Industry, Bridges, Storage Tanks, Medical Industry, Civil Engineering, Pressure Vessels, Reactor Tanks, and Heat Exchangers, Rotors, Impellers and Shafts, Power Plants, Petrochemical, Shipbuilding Industry, Pumping Stations, Nuclear Power.
EN 1092-1 Type 02 Flange is Covered with Plastic Cloth and Packed in Wooden Box, Wooden Pallet and Wooden Fumigated Carrate. Our Packaging is Fully Waterproof and Safe for Transport with Proper Strips on Wooden Box, having Lifting Point.
We Export EN 1092-1 Type 02 Flanges to Saudi Arabia, Iran, Iraq, United Arab Emirates, Qatar, Bahrain, Oman, Kuwait, Turkey, Egypt, Yemen , Syria, Israel, Jordan, Cyprus, Singapore, Malaysia, Indonesia, Thailand, Vietnam, South Korea, Japan, Sri Lanka, Maldives, Bangladesh, Myanmar, Taiwan, Cambodia, Argentina, Bolivia, Brazil, Chile, Venezuela, Colombia, Ecuador, Guyana, Paraguay, Uruguay, United States Of America, Canada, Mexico, Panama, Costa Rica, Puerto Rico, Trinidad And Tobago, Jamaica, Bahamas, Denmark, Russia, Norway, Germany, France, Italy, United Kingdom, Spain, Ukraine, Netherlands, Belgium, Greece, Czech Republic, Portugal, Hungary, Albania, Austria, Switzerland, Slovakia, Finland, Ireland, Croatia, Slovenia, Malta, Nigeria, Algeria, Angola, South Africa, Libya, Egypt, Sudan, Equatorial Guinea, The Republic Of Congo, Gabon, Europe, Africa, Asia, North America, South America, Middle East, Far East.etc
We Supply EN 1092-1 Type 02 Flanges Andhra Pradesh, Arunachal Pradesh, Assam, Bihar, Chhattisgarh, Goa, Gujarat, Haryana, Himachal Pradesh, Jammu and Kashmir, Jharkhand, Karnataka, Kerala, Madhya Pradesh, Maharashtra, Manipur, Meghalaya, Mizoram, Nagaland, Odisha, Punjab, Rajasthan, Sikkim, Tamil Nadu, Telangana, Tripura, Uttar Pradesh, Uttarakhand, West Bengal, Mumbai, Navi Mumbai, Pune, Nashik, Nagpur, Solapur, Kolhapur, Ambernath, Ahmednagar, Latur, Ahmadabad, Surat, Rajkot, Vadodara, Panaji, Madgaon, Chennai, Kolkata, Hyderabad, Bengaluru, Delhi, New Delhi, Ludhiana, Chandigarh, Raipur, Bhopal, Jamshedpur, Vishakhapatnam, Cochin, Ghaziabad, Noida, Gurugram, Bhillai, Durgapur, Vijaywada, Kanpur etc.
EN 1092-1 Type 02 Flanges are vital Components in Piping Systems, offering Reliable and Standardized Connections for various Industries. This guide has provided an overview of the key aspects of EN 1092-1 Type 02 Flanges, including their definition, classification, Dimensions, Materials, Installation, and Applications. by following the Standard Guidelines and Considering Specific Project Requirements, Professionals can ensure safe and efficient piping systems that meet Industry Standards and Regulations
EN 1091-1 Long Weld Neck Flanges, EN 1091-1 Stainless Steel Flanges, EN 1091-1 Carbon Steel Flanges, EN 1091-1 Alloy Steel Flanges, Din en 1092 1 flange dimensions pdf, din en 1092-1 flange dimensions, En 1092 1 flange dimensions, en 1092-1 flange dimensions pdf, en 1092-1 flange specifications, en 1092-1 flange standard, en 1092-1 flange weight, en 1092-1 pdf free download, en 1092-1 pn16 flange dimensions, en 1092-1 standard pdf, en 1092-1:2018 pdf free download